Model 215 Alpha Frisker w/ Model 215-20 Charging/Cal Stand

Part Number - 48-3531

INDICATED USE: Alpha frisking, hand monitor with alarm
DETECTOR: Alpha air proportional probe with integrated electronics
OPERATION: While sitting in charging/calibration stand, probe may be used as a hand monitor. Red LED, click audio, and a steady-tone alarm audio warn of contamination. Probe may also be picked up from charging stand and used as a frisker for up to 30 minutes before recharge. Maximum recharge time is 20 minutes to full charge, maximum time to operation is 5 minutes.
DISPLAY: Red LED - Alpha pulse or continuous on alarm
                  Amber LED - Trouble
                   Green LED - OK
WINDOW: 0.4 mg/cm² aluminized mylar with aluminum screen (79% open).
Can be easily replaced by removal of six screws on back of probe
WINDOW AREA:
     Active - 139 cm²
     Open - 110 cm²
EFFICIENCY(4pi geometry): Typically 10%- 239Pu
AUDIO: 85 dB at 12 inches
OPERATING VOLTAGE: Altitude sensitive
     Sea level - 1950 volts
     2000 feet - 1900 volts
     5000 feet - 1825 volts
    7000 feet -1775 volts
COUNTER THRESHOLD SETTING: 4 mV
CALIBRATION DUE DATE: When exceeded, amber trouble light will illuminate (real time clock located in charging/calibration stand)
CONSTRUCTION: Conductive plastic body with internal sealed electronics
TEMPERATURE RANGE: -4° F(-20° C) to 122° F(50° C)
May be certified for operation from -40° F(-40° C) to 150° F(65° C)
SIZE: Probe: 9.2” (23.8 cm)H X 3.8” (9.65 cm)W X 1.76” (4.47 cm)D
Charging/Calibration Stand: 0.75” (1.9 cm)H X 0.825” (2.10 cm)W X 1.54” (3.9 cm)L
WEIGHT: 0.75 lbs. (0.34 kg)
POWER: Model 215’s internal capacitors provide power for 30 minutes in non-alarming condition.

ACCESSORIES:
• Model 215-20 Charging/Calibration Stand interfaces with a personal computer and uses infrared communications to set parameters and run automatic plateau routines. The stand’s input power is +15V(+12V minimum to +20V maximum) at 100mA maximum. Four charging/calibration stands can be interconnected to run from a single 0.5A wall mount power supply.

• Model 215 Calibration Software (Part No.: 1370-080) available to assist in changing parameters and determining operational settings.

Model 215-20
Charging/Calibration Stand
Part No.: 48-3567

Model 215 shown
Model 215-20 Charging/Calibration Stand

M215-cmb

Model 215 Alpha Frisker and
charging/calibration stand shown separately

Return to New Products Page

Ordering Info.          Manual

Return to ludlums.com

Copyright © 2001 Ludlum Measurements, Inc.
For comments or suggestions please contact webmaster at: mtruitt@ludlums.com
Page last updated: March 2008


	Part Number - 48-3531

INDICATED USE: Alpha frisking, hand monitor with alarm DETECTOR: Alpha air proportional probe with integrated electronics OPERATION: While sitting in charging/calibration stand, probe may be used as a hand monitor. Red LED, click audio, and a steady-tone alarm audio warn of contamination. Probe may also be picked up from charging stand and used as a frisker for up to 30 minutes before recharge. Maximum recharge time is 20 minutes to full charge, maximum time to operation is 5 minutes. DISPLAY: Red LED - Alpha pulse or continuous on alarm Amber LED - Trouble Green LED - OK WINDOW: 0.4 mg/cm² aluminized mylar with aluminum screen (79% open). Can be easily replaced by removal of six screws on back of probe WINDOW AREA: Active - 139 cm² Open - 110 cm² EFFICIENCY(4pi geometry): Typically 10%- 239Pu AUDIO: 85 dB at 12 inches OPERATING VOLTAGE: Altitude sensitive Sea level - 1950 volts 2000 feet - 1900 volts 5000 feet - 1825 volts 7000 feet -1775 volts COUNTER THRESHOLD SETTING: 4 mV CALIBRATION DUE DATE: When exceeded, amber trouble light will illuminate (real time clock located in charging/calibration stand) CONSTRUCTION: Conductive plastic body with internal sealed electronics TEMPERATURE RANGE: -4° F(-20° C) to 122° F(50° C) May be certified for operation from -40° F(-40° C) to 150° F(65° C) SIZE: Probe: 9.2” (23.8 cm)H X 3.8” (9.65 cm)W X 1.76” (4.47 cm)D Charging/Calibration Stand: 0.75” (1.9 cm)H X 0.825” (2.10 cm)W X 1.54” (3.9 cm)L WEIGHT: 0.75 lbs. (0.34 kg) POWER: Model 215’s internal capacitors provide power for 30 minutes in non-alarming condition. ACCESSORIES: • Model 215-20 Charging/Calibration Stand interfaces with a personal computer and uses infrared communications to set parameters and run automatic plateau routines. The stand’s input power is +15V(+12V minimum to +20V maximum) at 100mA maximum. Four charging/calibration stands can be interconnected to run from a single 0.5A wall mount power supply. • Model 215 Calibration Software (Part No.: 1370-080) available to assist in changing parameters and determining operational settings.
Model 215-20 Charging/Calibration Stand Part No.: 48-3567 Model 215 shown Model 215-20 Charging/Calibration Stand		Model 215 Alpha Frisker and charging/calibration stand shown separately

*Return to New Products Page*

Ordering Info. Manual

*Return to ludlums.com* Copyright © 2001 Ludlum Measurements, Inc. For comments or suggestions please contact webmaster at: mtruitt@ludlums.com Page last updated: March 2008