Software Downloads
Last Updated May 13, 2013
Model 9DP Pressurized Ion Chamber
Model 53 Personnel Gamma Portal Monitor
- Version 1.1.0 - Full installation package for the Supervisor software.
Model 54 Small Article Monitor
- Version 1.0.4 - Full installation package for the Supervisor software.
Model 250 Software
- Version 1.0.4 - Calibration Software
Model 375
- Version 39801N16 - Latest Ethernet board firmware for use with Web Page and Service software.
- Setup Utility - Model 375 Setup Utility 1.5.2.
- Subnet Searcher - Search network for Model 375s.
Model 464 Software
- Version 1.2.0 - PC Interface software (DOS).
Model 730 Series MCA Software
- Version 2.33 - 1024 Channel MCA Software.
Model 2200/2000 Software
- Version 1.2.1 - PC Interface software.
Model 2241 Series Software
- Version 1.1.0 - PC Logger software. (Note: Not compatible with ASCII Output firmware)
- Version 1.2.0 - PC Calibrator software. (Note: Not compatible with ASCII Output firmware)
- RS-232 Data Output PDF - Document detailing the RS-232 data output for various firmware versions.
Model 2350 Software
- Version 1.2.1 - PC Interface software.
- Excel Barcode Spreadsheet - Excel spreadsheet for generating barcodes with checksum.
- OpenOffice.org Barcode Spreadsheet - OpenOffice.org spreadsheet for generating barcodes with checksum.
- Free 3 of 9 Barcode Font - Font used in above spreadsheet.
Model 2360 Software
- Version 2.2.0 - PC Interface software.
- Excel Barcode Spreadsheet - Excel spreadsheet for generating barcodes.
- OpenOffice.org Barcode Spreadsheet - OpenOffice.org spreadsheet for generating barcodes.
- Free 3 of 9 Barcode Font - Font used in above spreadsheet
Model 2360-8 Software
- Version1.0.4 - PC Interface software.
Model 2363 Software
- Version 1.4.1 - PC Interface software.
Model 3030 Software
- Version 1.4.8 - PC Interface software.
Model 3030P Software
- Version 1.6.2 - PC Interface software.
Model 4304 Software
- Version 1.2.0 - Single Quad Counter software set operating parameters, starts/stops counts, sets operating parameters and runs calibration routines.
Model 4525 Software
- Version 2.3.0 - Supervisor Software. Requires firmware 39651n16.
- Version 2.6.1 - Supervisor Software. Requires firmware 39651n22, 39651n23, or 39651n28.
- Version 2.9.5 - Supervisor Software. Requires firmware 39651n30.
- Version 3.1.3a - Supervisor Software. Requires firmware 39651n31 or higher.
- Version 3.2.4 - Supervisor Software. Requires firmware 39651n31/39651n33 (Neutron) or higher.
- Version 3.4.0 - Supervisor Software. Requires firmware 39653n01 (Neutron).
- Version 3.4.0a -Supervisor Software. Requires firmware 39653n01 (Neutron).
- Customer Upgrade Procedures - Software and firmware installation procedures.
- ipsetup - IP Setup Utility.
- White Box Computer Drivers - Motherboard and printer drivers for the original "white box" computer.
Model 4609-3 Software
- Version 1.0.0 - Model 4609-3 Counter Software.
Model 4906AB - Software
- Version 1.2.6 - 4906AB Supervisor Software Installer
- Dec 2012 Update - Calibration and Testing Procedure
- Dec 2012 Update - System Checkout Procedure
- Dec 2012 Update - Operator's Manual
Model 4612 Software/Firmware
The Model 4612 counter is a twelve detector SCA (Single Channel Analyzer) with PC control of all necessary operating parameters. Programming the host board requires the Analog Devices Windows Serial Downloader application. To update the host firmware:
- Download the Windows Serial Downloader software and the appropriate .HEX file below. Right click on the firmware link and select "Save As" to download the .HEX file.
- Disconnect power to the Model 4612 Counter.
- Unscrew the host board and locate the 2-pin debug connector next to the EMUL connector.
- Place a jumper on the debug connector and insert the host board back into the chassis.
- Reconnect power.
- Run the Windows Serial Downloader application.
- Click the Configuration button and select to correct Serial Port. Click OK.
- Click the download button and select the .HEX file. The host board should now be flashed.
- Disconnect power to the Model 4612 Counter.
- Remove the jumper from the host board and screw it back to the chassis.
Host Board Firmware
- 34413N02 - Requires Software 1370-081 - Shipping on all new instruments.
- 34403N11 - Requires Software 1370-045
Software
There are two versions of the software depending on the host firmware.
- 1370-081 - Latest version of software. Requires firmware version 34413N02 or higher.
- 1370-045 - Requires firmware version 34403N11 or earlier .
